- Isolation Booths (12)
Studio Acoustic Foam Treatment (129)
- - Acoustic Foam Panels (29)
- - Acoustic Foam Tiles (33)
- - Melamine Acoustic Foam (14)
- - Bass Traps (10)
- - Acoustic Ceiling Tiles (2)
- - Acoustic Floor Tiles (3)
- - Room Analysis (1)
- - Isolation Equipment (7)
- - Acoustic Tile Kits (16)
- - Bass Trap Kits (4)
- - Starter Kits (8)
- - Installation Tools (1)
- - Diffusors (1)
- Cinema & Listening Room Acoustics (25)
- Office Acoustics (46)
- Soundproofing Products (52)
Soundproofing Mat - 1.25m by 3m by 2mm thick - 5kg Membrane
Dimensions - 1.25m by 3m by 2mm thick per sheet (nominal) - 5kg per square meter
A 2mm thin soundproofing membrane mat designed to block and reduce airbourne noise through stud walls and timber joisted floors and ceilings. A thin, effective mineral loaded soundproofing mat designed to block and reduce airborne noise transmission through stud partitions, timber joisted floors and ceilings.
Please note: Soundproofing Mat is a very heavy product and larger orders may require help with offloading!
SoundProofing Mat is a heavy layer mineral loaded soundproofing mat nominally 2mm thick with excellent sound blocking qualities and will give significant sound reduction through lightweight structures when used as a sound barrier.
It is equal to lead of the same mass in effectiveness and acts as a thin de-coupling sound blocker in stud walls and timber floors. Biggest sound insulation improvements can be achieved when it is used as one layer sandwiched between two sheets of plasterboard on lightweight structures.
One layer of Soundproofing Mat has an insulation value of 24dB.
Two layers has an insulation value of 29dB.
Three layers has an insulation value of 32dB.
The above values are calculated when the sound proofing mat is hung as a curtain. It does not mean this will increase a structure by the same degree of sound proofing but simply proves that the mats are a highly efficient method of improving the sound insulation of stud walls, floors and ceilings.
Normally, a 3dB improvement is equal to a 50% loss in the volume of noise depending on where you are standing!!
Use on Walls
Soundproofing Mat is not suitable for glueing directly onto masonry or stud walls. To get the best results from this product, it should be sandwiched between two layers of high density Acoustic Plasterboard as part of a stud partition soundproofing solution as detailed above and is suitable to help reduce loud noise nuisance when used in this way.
If you are suffering from a small amount of noise, omitting loud music and bass, you may wish to look at our Basic Wall System instead of the mats.
With louder noise such as music at high volumes, we recommend using the Studio Wall System. The soundproofing mat is sandwiched between two layers of acoustic plasterboard which in turn are screwed to the bars.
Alternatively you can glue the Soundproofing Mats directly to an exisiting stud wall using our Contact Adhesive before adding more acoustic plasterboard. The additional acoustic plasterboard should be fixed immediately to hold the Soundproofing Mat securely in place and will help reduce the noise by acting as a decoupler. Normally fixed to original panels of metal, wood and plasterboard etc, this acoustic mat is a 'deadsheet’ that is particularly effective at improving the sound insulation value of timber floors and stud partitions.
Use on Floors
First ensure the floorboards are securely screwed to the floor so as not to squeak when walked over. Then use our Acoustic Sealant and fill in the joints between the floorboards and around the edge of the room making the floor is as airtight as possible. Then using our Contact Adhesive glue the layers of soundproofing mat to the timber floor. This will dramatically reduce airborne noise penetrating the floor from below or any airborne noise you create being transmitted to below but will not significantly reduce any footfall or impact noise.
PLEASE NOTE !! OUR SPECIAL AEROSOL ADHESIVE IS A CONTACT ADHESIVE. ONCE THE PRODUCT IS OFFERED UP TO THE SURFACE AND STUCK IT CANNOT BE EASILY RE POSITIONED.
Because Soundproofing Mat is produced from recycled manufacturing materials, there may sometimes be a 'rubbery’ smell when the product is first unpacked. Usually any smell will dissipate within a few days but as a precaution, we advise applying a thin layer of polythene over the insulation on walls and floors before the final covering is installed to seal in any possible smells.
Dimensions - 1.25m by 3m by 2mm thick per sheet (nominal) - 5 kg per square meter
Write a reviewYour Name:
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: