SilentMat16 Acoustic Matting for LVT | 1.6mm | 15m × 1m
SilentMat16 is a 1.6mm acoustic matting designed to be bonded to concrete and screed subfloors beneath glue-down LVT. The product works by introducing a resilient layer between the subfloor and the floor finish — absorbing impact energy from footfall before it can transmit through the floor structure. At 1.6mm nominal thickness it adds no meaningful build-up and does not raise floor heights, making it suitable for renovation projects where door clearances and threshold heights are fixed.
Each roll covers 15m² and weighs 25kg. The product must be used with glue-down LVT of a minimum 2mm thickness — thinner LVT risks telegraphing through seams and joints in the underlay. When installed with 2.5mm LVT, SilentMat16 achieves 18dB of impact sound reduction. The product is compatible with underfloor heating systems.
Applications
-
Residential floors — glue-down LVT — suitable for apartments and upper-floor rooms where impact noise from footfall is the primary concern. SilentMat16 must be bonded to the subfloor; it is not suitable for loose-laid or floating floor installations. Use with LVT of 2mm minimum thickness to avoid telegraphing at seams.
-
Commercial floors — offices and retail — where consistent foot traffic and point loading from furniture and equipment are present, SilentMat16 provides impact noise reduction without raising floor height. Note that the resilient layer introduces a degree of softness underfoot — seek advice before specifying in areas with extreme point loading or critical lateral lighting.
-
Underfloor heating systems — SilentMat16 is compatible with underfloor heating. Confirm compatibility with the UFH system manufacturer before specifying, and ensure subfloor temperature does not fall below 10°C during installation.
Product Benefits
-
18dB impact sound reduction with 2.5mm LVT. Tested performance is achieved when installed with glue-down LVT of 2.5mm thickness. Impact sound reduction is measured as the reduction in transmitted noise level — each 10dB represents an approximate halving of perceived loudness.
-
1.6mm profile — no increase in floor height. At 1.6mm nominal thickness, SilentMat16 adds negligible build-up and does not require adjustment to door frames, thresholds, or skirting in most installations.
-
Compatible with underfloor heating. The product does not impede heat transfer from underfloor heating systems and can be specified in heated floor assemblies.
-
25kg per roll — 15m² coverage. Each roll covers 15m² at 1m wide × 15m long, with a 5% waste allowance recommended for cutting and fitting.
Installation
Ensure the subfloor is level, clean, and free from dust and debris. Fill any cracks or voids with AC95 Acoustic Sealant and allow a 24-hour acclimatisation period at 18–35°C before installation. Bond SilentMat16 to the subfloor using a recommended adhesive, butt all joins tightly, and seal the perimeter gap with AC95 Acoustic Sealant. Once fully bonded, install glue-down LVT at 90° to the SilentMat16 to minimise coinciding joints. Use LVT of 2mm minimum thickness.
Technical Details
| Product Name |
SilentMat16 |
| Product Size |
15m × 1m |
| Product Thickness |
1.6mm |
| Area Covered Per Roll |
15m² |
| Product Weight |
25kg |
| Impact Sound Reduction |
18dB (with 2.5mm glue-down LVT) |
| Minimum LVT Thickness |
2mm |
| UFH Compatible |
Yes |
Preparation
The floor must be prepared prior to installation by ensuring all surfaces are level and smooth, free of dust and debris and any holes / cracks or similar filled and sealed with AC95 Acoustic Sealant.
The product must be allowed to acclimatise to the environment for 24 hours prior to installation, the temperature of the room should be at least 18°C and relative humidity below 75%. In general working practices outlined in (BS8203: 2017 Code of practice for installation of resilient floor coverings) should be followed.
Perimeter Considerations
Flanking issues can seriously detract from the performance of acoustic flooring, this occurs where sound is able to bypass flooring treatments through adjoining surfaces or through a weak area of the structure. This can both reduce the quality of the flooring and detract from the performance when looking to pass Part E Building requirements. Ensure that the junction between floor and wall contains no defects and the structure and build up of the wall and floor structure does not negatively affect the underlay and floor treatment.
Installation Of SilentMat16
The ideal installation temperature is between 18-35°C with a maximum air relative humidity of 65%. The subfloor temperature should not fall below 10°C, it is important that the flooring and underlay are stored on site at the same temperature as the areas to be installed.
SilentMat16 must be bonded to the subfloor. It is not essential to commence installation in the centre of the room; it is generally more practical to commence along the longest wall running the rolls in parallel. Wherever possible the product should be installed so that the joints run with the direction of the main light in the installation area rather than against it. Ideally this will also be at 90 degrees to the finished floor so that the chance of coinciding joints is minimised. The product should be dry laid into workable areas and cut at least 50mm over the length required and allowed to relax for the acclimatisation period as advised above. After acclimatisation the underlay should then be cut using a utility knife and straight edge and a gap of around 3mm should be left around the perimeter to allow for any expansion. The SilentMat16 should not be in direct contact with any wall, column or skirting board that has not been isolated using a perimeter isolation strip. The product should be adhered to the subfloor using a recommended adhesive strictly in accordance with the installation instructions of the adhesive manufacturer. It is particularly important to refer to the adhesive manufacturer’s advice in respect of trowel sizes, application rates/coverages and open times.
Only spread enough adhesive to cover a workable area, and after the required open time lay the product into the adhesive and smooth out from the centre using a carpet glider or hand roller to ensure that the product is fully into the adhesive and all air bubbles are released. The SilentMat16 should then be fully rolled into the adhesive using a 68kg articulated flooring roller to ensure full adhesion along the entire length and width of the product. All edges should be butt jointed ensuring that all seams and joints are smooth without any voids but not too tight. Open seams with any gaps will “telegraph” through most LVTs, so it is very important that the underlayment work is as smooth and well seamed as possible.
Installation
Once the SilentMat16 is fully bonded to the subfloor, this time will depend on the adhesive used but usually after 24 hours, the LVT can be installed. SilentMat16 should be used with glued down LVT products of a minimum thickness of 2mm so that issues of “telegraphing” through are minimised. To provide noise improvement the product has to have a level of resilience to absorb impact energy and as such adds a degree of softness to the overall floor. This must be born in mind for areas where critical lateral lighting may be present, also please seek advice for installation areas where there may be equipment with extreme point loading. The LVT should be installed following the instructions of the LVT manufacturer using a suitable approved adhesive with correct notched trowel size. SilentMat16 has limited porosity so some wet set adhesives may take longer to go off. Ideally the LVT should be installed at 90° to the SilentMat16 so that the chance of coinciding joints is minimised. It is important to leave a small gap so that the finished floor does not come into contact with any part of the perimeter to avoid flanking problems. The gap should be filled with AC95 Acoustic Sealant.
To quickly find out the shipping cost for your order simply add the required items to your cart. Place your cursor over the cart icon at the top of the page. Click on "Calculate Cart Shipping". Select your country and region and enter your postcode. The shipping rate will be displayed. If your country is not listed please contact us for a shipping quote.
UK Shipping Charges For Most Products
Orders with a value of £0.00 to £54.99 have a £7.00 carriage charge with tracked next working day delivery.
Orders with a value of 55.00 to £99.99 have a £12.00 carriage charge with tracked next working day delivery.
Orders with a value of £100.00 or more qualify for free next day shipping.
Excluded Items
For carts which contain Plasterboard, Soundproofing Mat, SilentBoard, QuietPanel, Silent Floor Ultra, M20 and R10 the following charges apply
£8.00 carriage for the first item and £4.00 carriage for every item added up to a maximum charge of £75.00.
Some soundproofing items have a minimum order due to shipping constraints.
Bulk Products have a £75.00 pallet charge per item.
Returns
Our policy lasts 30 days. If 30 days have gone by since your purchase, unfortunately we can’t offer you a refund or exchange. To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.
Non-returnable items:- Made to order items such as our Office Acoustic Panels and High End Audio Acoustic Panels, Gift cards.
To complete your return, we require a receipt or proof of purchase. Please contact us for your return authorisation number. Once your return is received and inspected, we will send you an email to notify you that we have received your returned item.
Exchanges
We only replace items if they are defective or damaged. If you need to exchange it for the same item, send us an email at info@advancedacoustics-uk.com and send your item to: Advanced Acoustics LTD, Unit B, Maunside, Green Line Industrial Estate, Mansfield, NG18 5GU, United Kingdom.
